Educational trainer

PM-ENTERPRISE

The DIGITAL LAB is intended for elementary as well as advance training of digital electronics. The digital lab covers regular digital circuits by solder-less interconnections on breadboard and as well as compatible with all optional modules through use of 2mm brass terminals and patch cords. Various clock generators, logic level input/output indicators and DC regulated power supplies etc. are in-built. The unit housed in attractive en

FEATURES
High level, high quality digital-analog trainer

Includes Two Digital Meters one for 20V Voltmeter and other for 200mA Ammeter

Combines all essential functions of analog and
digital experiment with removable breadboard,
Includes DC power supply function generator, two pulse switches, 8 ohm 0.25W speaker etc.

Solder-less,breadboard
Interconnected with tie points Nickel plated contact, fitted with all DIP sizes and all components with lead and solid wire. It can be changed and replaced for different purposes and can be connected with demonstration panel. Therefore, it is very convenient for both teachers and students 
DC power supply 

Fixed DC Output

: ±5V, ±12V @ 500Ma

   

Variable DC Output

: Dual 0~30V, 0~ -30V @ 500mA

   

 

AC power supply

: 0~5~0 VAC,12~0~12VAC

   

Potentiometers:

:1Kohm,10Kohm

Function generator

 

Frequency range

: 1Hz ~ 10Hz

   
 

: 10Hz ~ 100Hz

   
 

: 100Hz ~ 1KHz

   
 

: 1 KHz ~ 10 KHz

   
 

: 10 KHz ~ 100 KHz

   

Amplitude

 

Sine wave output

: 0 ~ 6 Vpp variable @ 1Hz~1MHz in 5 steps

   

Triangle wave output

: 0 ~ 6 Vpp variable @ 1Hz~ 300KHz in 5 steps

   

Square wave output

: 0 ~ 5 Vpp variable @ 1Hz~400KHz in 5 steps

   

TTL mode output

: 5V@1Hz~1MHz in 5 steps

   


Two digits of 7 segment LED display

One pulse switch
Push buttons to generate inverting and non inverting pulses supported with de-bounce elimination

Data switches
Toggle switches and corresponding output point. When switch is set at “Down” position, the output is LOW level, contrarily it is to be 'High' level while setting at “Up” position

Speaker
8ohm/0.5W to be used for load

Four channel adaptor
The two banana sockets and BNC jacks suitable for the trainer to be connected with peripherals

Sixteen bit LED display
Red LEDs separate input terminals. The LED will be lighted up when input is at “High level ”and it will be turned OFF when it is at “No Input” or at “Low level”

Packing list

  • Instruction manual hard copy and Soft Copy In CD.
  • Power supply mains 3 pin cord
  • Patch cords

Topics of Experiments :

 

 

  1. Discrete component module
  2. Series and Parallel Resistance Circuits module
  3. Basic ohm law , Kirchoff's Laws , voltage and current measurement , potentiometer as voltage divider .
  4. Thevenin's Theorem
  5. Magnetism experiments modules
  6. Alternating Current Measurement
  7. RC, RL, RLC trasient characteristics  and resonance circuits module .
  8. Rectifier  and Filter Circuits module
  9. Characteristics of diode , zener diodes  and leds
  10. Power supply circuit modules
  11.  Junction Transistors characteristics modules

Common Emitter Amplifier Characteristics

  1. The Emitter Follower Amplifier
  2.  Single and 2 stage RC coupled amplifier
  3. Push pull class b amplifier module
  4. differential Amplifier module
  5. FET characteristics module
  6. FET common source amplifier
  7. Op amp characteristics module
  8.  Op amp summing and diffrential amplifier module
  9. Integrator and diffrentiator  module
  10. Op amp oscillator RC phase shift module
  11. Op amp wein bridge oscillator module
  12. 555 as monostable multivibrator
  13. 555 as astable multivibrator
  14. 555 as bistable multivibrator
  15. Logic gate module
  16. Adc module
  17. Dac module
  18. Demoragn and logic circuit module

More Products of Analog Communication